F150 Coolant Change

 

Home
Up

May 7, 2002

F150 Coolant Change*

*1998 Ford F150 4x4 with 4.6L V-8, 4R70W 4spd electronic automatic, with air conditioning.

NOTE: Follow these instructions at your own risk.

Tools needed for the job:

  • Safety glasses
  • Rubber gloves
  • Ratchet, 17mm socket
  • 19mm open end wrench
  • piece of 1/2inch ID hose (any)
  • Suitable drain pan
  • Funnel
  • Rags/Paper towels
  • Loctite liquid
Parts needed:
  • 2 jugs good quality antifreeze, preferably low phosphate (4L/1gal)
  • 2 jugs distilled water (4L/1gal)

Time required to complete:

  • 1/2 to 1 hour depending on how quick you are. Draining is the slow part.

Note: wear safety glasses while under the vehicle for eye protection as there's lots of dirt and grime under there just waiting to drop into your eyes.

Procedure:

  1. Wait until the vehicle has cooled off for at least 1/2hr if you've just driven it to avoid getting a "hot coolant treatment"... burns hurt!
  2. Place your drain pan under the passenger side front wheel well.
  3. Open the coolant expansion tank to allow air in to help drain the system.
  4. Locate the drain spigot, bottom of radiator, inside engine compartment, passenger side.
  5. Fasten your 1/2inch hose (about 6-12 inches long) on the spigot's spout which points to the passenger side. Use the 19mm open wrench to loosen the white drain bolt. Make sure your drain container catches the coolant as some will leak from the spigot drain bolt as well. Left arrow shows hose on spligot, right arrow shows spigot drain bolt. Bottom picture shows 19mm wrench loosening the spigot bolt.
  6. Let it drain.
  7. Take your garden hose and flush out the expansion tank, then let that drain also.
  8. When it's finished draining, pull the hose off the spigot and tighten the bolt. Don't overtighten it... it's plastic so 1/16 of a turn max.
  9. Locate the drain plug on the block. On my 98' 4x4 I found the plug just below the rear-most frost plug in the block on the driver's side accessible. Use a 17mm socket & wrench. They use loctite so you'll have to reef on there like a #%$@&!!#@ so watch your knuckles. Wear leather gloves for safety. My engine block heater is also in that frost plug so it's a tight socket fit.   The arrow shows the plug, pic taken from front of truck underneath looking up and rear-ward on driver's side of the motor. Closeup shown:
  10. Make sure you have your drain pan underneath the motor before fully removing the plug in the block. Haynes manual shows a different picture, they say drain plugs are 1 inch above oil pan. Sort of accurate but their picture isn't accurate. There are too many brackets and the starter, etc in the way on the passenger side. If you have all day you might want to attempt it, I didn't.
  11. Let it drain. Now put some loctite on the drain plug threads after cleaning them off/drying them. Make sure the drain hole in the block is dry with paper towel. Then re-insert the plug. Put it in good and tight.
  12. Start filling in the coolant using your funnel. First the two jugs of antifreeze, then follow until full with distilled water. Let the engine come up to temperature and then check it again.
  13. If the engine doesn't heat up fast enough you can always do a drive around the block or to the corner store. Then check the level again. Be very careful with opening the expansion chamber coolant cap while the engine is at operating temperature. This is very dangerous. If you have to then use a couple of rags to cover the cap, and open it slowly just a notch to let the pressure escape. If coolant comes rushing out close it immediately. Otherwise you can open it once the pressure is released.

Tips/Hints:

  • always use distilled water, not spring water or from the garden hose when doing the final fillup with coolant. The mineral/sediment content in regular water will eventually drop out of suspension and clog your heater core/radiator later on as the coolant ages.
  • if you have the time use a commercial engine flush. Drain the coolant as shown above, fill with engine flush and water. Run it up to operating temperature. Let it cool 1/2hr. Drain complete system again (I'd flush with plain water once more to get all the flush chemical out). Then fill up with distilled water/antifreeze. Engine flush can get rid of accumulated dirt/grime/sediment/mineral deposits. I didn't have time for this it this time around.
  • dispose of the coolant at a service facility or recycling depot. Don't pour it down the drain.
  • total coolant capacity of my 98' 4.6L 4x4 with air conditioning is 18.9L!! I didn't get that much in. It's best to try and reach the drain plug on the other side of the block but I wasn't that ambitious.
  • Ideal mix for coolant v.s. distilled water is 50/50% and up to 60/40% (more antifreeze than water). 60/40 gives the most protection in extreme cold and extreme heat before boil-over.

Cost:

  • antifreeze is about $10-12CDN per 4L/1gal jug, you'll need a couple.
  • distilled water was around $3CDN per 4L/1gal jug, you'll need 1 1/2.
 

Copyright 2001-2003  Peter Ferlow