topbanner.jpg (19460 bytes)



 
 

AMSOIL By-Pass Oil Filters
To request a free product catalog.
For Pricing or to order call Toll Free 
1-800-956-5695
Use your Customer # 327600

By-Pass Oil Filters

Engine wear is caused by dirt particles larger than 5 microns. The AMSOIL By-Pass Oil Filter removes particles as small as 1/10 of a micron, virtually eliminating engine wear.
 Product Code: BF

(some mechanical ability required for installation)
AMSOIL By-Pass Oil Filters filter all the oil in a six-quart system in about five minutes at an average engine speed equivalent to 45 mph.

Call and order a free G-254A to find out how a TRIGARD Oil Analysis Plan can greatly extend your oil drain intervals.

"When we took this Chevrolet 396 engine apart (using AMSOIL Synthetic 10W-40, Reusable Air Filter and By-Pass Oil Filter), it was in the best condition of any engine I have ever seen. It looked like it had about 80,000 miles on it instead of over 535,000. The bearings were not even worn to the brass and the rings were not worn out. It was clean inside, no sludge or carbon at all."
K.A., Liberal, Kansas

PRODUCT DESCRIPTION

The AMSOIL By-Pass Oil Filter provides the best possible filtration protection against wear, oil degradation, rust and corrosion. Working in conjunction with the engine’s full-flow oil filter, the AMSOIL By-Pass Filter operates by filtering oil on a "partial-flow" basis. It draws approximately ten percent of the oil at any one time and traps the extremely small, wear-causing contaminants and water that full-flow filters can’t remove. The AMSOIL By-Pass Filter typically filters all the oil in the system several times an hour, so the engine continuously receives analytically clean oil.

G498BYPA.jpg (13940 bytes)

 
Frame Mount 1
Click for larger image		 Frame Mount 2
Click for larger image		 Under Hood Mount 1
Click for larger image

PRODUCT DESCRIPTION

The AMSOIL By-Pass Oil Filter provides the best possible filtration protection against wear, oil degradation, rust and corrosion. Working in conjunction with the engine’s full-flow oil filter, the AMSOIL By-Pass Filter operates by filtering oil on a "partial-flow" basis. It draws approximately ten percent of the oil at any one time and traps the extremely small, wear-causing contaminants and water that full-flow filters can’t remove. The AMSOIL By-Pass Filter typically filters all the oil in the system several times an hour, so the engine continuously receives analytically clean oil.

Typical Installation Diagram for 
BMK-11 and BMK-12 Kits.
By-Pass Filter Photos
BMK-11 BMK-12 BMK-13 BMK-15 & BMK-16

 

Sample Kit Size Measurement

Reduces Wear

Approximately 60 percent of all engine wear is caused by dirt particles in the 5 to 20 micron range. These particles can get inside the precision clearances between engine components and cause severe damage. While full-flow oil filters generally stop contaminants no smaller than 25 to 40 microns, the AMSOIL By-Pass Filter effectively stops particles smaller than one micron in size, substantially reducing engine wear.

Prevents Oil Degradation, Rust and Corrosion

Water enters motor oil as a combustion by-product or as a condensate. Water contamination of the motor oil can cause extreme engine damage. Water causes metal surface rust and corrosion, which increases friction and wear and deteriorates the close-fitting tolerances between engine components. In addition, water reacts with other oil contaminants to form corrosive acids, which also damage metal components. The AMSOIL By-Pass Filter removes water, reducing the risk of oil degradation, engine rust and corrosion.

Extends Oil Drain Intervals

Because the AMSOIL By-Pass Oil Filter removes water and particles smaller than one micron, it significantly increases the time oil can safely be left in the engine. In fact , engines using AMSOIL Synthetic Motor Oil and an AMSOIL By-Pass Oil Filter routinely show much lower rates of engine wear - even when the oil is used for significantly longer drain intervals - than engines using conventional products and conventional oil drain intervals. That saves motorists time and money and helps protect the environment by creating substantially less used oil.

Dual Remote Filter System

The AMSOIL Dual Remote Oil Filtration System converts an engine’s full-flow oil filter system into a full-flow/by-pass oil filtration system by attaching an AMSOIL Full-Flow Oil Filter and AMSOIL Spin-On By-Pass Oil Filter onto a remote mount. The Dual Remote System provides superior filtration efficiency, increased oil capacity and improved oil filtration accessibility.

Typical Installation Diagram for 
BMK-13, BMK-15 and BMK-16 Kits.

AMSOIL By-Pass Filter Replacement Chart

Type of Unit Stock Number Size (Approx.) Additional Oil Needed Crankcase Capacity Normal
Service Life b		 Applications
SINGLE SPIN-ON ELEMENTS

(Used with BMK-11 or any DUAL REMOTE SYSTEM)

 BE-90 Diam. = 4.5 in.
Height = 6 in.
With Mnt. = 8 in.		 1 qt. up to 9 qt. 25,000 miles or 1 year

(approximately 4 times normal drain interval)

 Pleasure Vehicles, Light Trucks and Smaller Commercial Applications
BE-100 Diam. = 4.5 in.
Height = 8 in.
With Mnt. = 10 in.		 1.5 qt. up to 15 qt.
BE-110 Diam. = 4.5 in.
Height = 10 in.
With Mnt. = 12 in.		 2 qt. up to 21 qt.
DUAL SPIN-ON ELEMENT

(Used with BMK-12 DUAL-GUARD)

 (2) BE-90's Diam. = 5 in.
Height = 9.5 in.
With Mnt. = 8 in.		 2 qt. 15 to 18 qt. 2 times normal oil drain interval Large Trucks, Construction, Farm and Industrial Equipment

(minimum sump capacity = 15 qt.)
(2) BE-100's Diam. = 5 in.
Height = 9.5 in.
With Mnt. = 10 in.		 3 qt. 15 to 30 qt.
(2) BE-110's Diam. = 5 in.
Height = 9.5 in.
With Mnt. = 12 in.		 4 qt. 15 to 42 qt.
LARGE CANISTER BY-PASS FILTERS BE-50 Diam. = 7.5 in.
Length = 10 in.		 8 qt. 15 to 30 qt.
BE-75 Diam. = 7.5 in.
Length = 15 in.		 12 qt. 15 to 42 qt.

a. Filters can be used on sumps of larger capacity but then require more frequent replacement.  Full details on service life included with filter installation instructions

b. Data determined in a non-turbo gasoline engine with AMSOIL 100% Synthetic Motor Oil and AMSOIL Full-Flow Oil Filter.  Service life varies in other engines (turbo and diesel) and with other oils and filters.

NOTES:

  1. Special adapters and hardware may be required for some installations.

  2. Contact AMSOIL INC. Technical Service for instructions before installing on vehicles with cast aluminum oil pans.

APPLICATIONS

Mount

Filter (Order separately unless noted)

BMK-11

BE-90, 100, 110

BMK-13

BE-90, 100, 110

SDF-15, 26, 34, 42, 57, 84, 96

BMK-15 (complete with filters)

SDF-26 and BE-100 (Filters Included)

BMK-16 (complete with filters

SDF-26 and BE-100 (Filters Included)

 

Vehicles with sump capacities greater 15 qts.

Mount

Filter

BMK-12 Dual Guard

Any size AMSOIL Spin-On By-Pass (mount requires 2 filters and all hoses and fittings)

Heavy-Duty Canister Type (Element Only)

BE-50, BE-75 (Replacement Element only for Lubrifiner 500 and 750 respectively.)
 

E-mail direct to Amsoil Dealer

Other Trusted Amsoil Websites:
AMSOIL - Your complete source for Amsoil Synthetic Oil
AMSOIL - On-Line Ordering
AMSOIL - Information about becoming an Amsoil Dealer
AMSOIL - Contact Information
AMSOIL - Helps take the bite out of high fuel prices
AMSOIL - Advantage of using Amsoil Synthetic Oil
AMSOIL - Independent Amsoil Dealer
AMSOIL - Reduce dependence on foreign oil
AMSOIL - Advanced technology for maximum performance


Other Links of Interest
Selkirk Truss - Engineered Floors & Roof Truss Systems
ThistleDee Kennels - Keeshond Breeders
C-Write - Learning tools for students from Grades 7-12